substitutions:
  device_name: presence_sensor # Change the device name here
  friendly_name: "Presense Sensor"

esphome:
  name: ${device_name}
  comment: "HMMD mmWave Sensor S3KM1110 - ${friendly_name}"
  on_boot:
    priority: 550.0
    then:
      - light.turn_on:
          id: led
          brightness: 100%
          red: 100%
          green: 0%
          blue: 0%

esp32:
  board: esp32-s3-devkitc-1
  framework:
    type: arduino

# Enable logging
logger:
  hardware_uart: USB_CDC

# Optional: Enable Home Assistant API (uncomment to use)
# api:
#   encryption:
#     key: !secret api_encryption_key

mqtt:
  broker: !secret mqtt_broker
  port: !secret mqtt_port
  username: !secret mqtt_username
  password: !secret mqtt_password
  reboot_timeout: 0s
  discovery: true
  birth_message:
    topic: "${device_name}/status"
    payload: "online"
  will_message:
    topic: "${device_name}/status"
    payload: "offline"
  on_connect:
    then:
      - light.turn_on:
          id: led
          brightness: 100%
          red: 0%
          green: 100%
          blue: 0%
      - delay: 3s
      - light.turn_off:
          id: led

ota:
  - platform: esphome
    password: !secret ota_password

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  power_save_mode: none

  manual_ip:
    static_ip: !secret device_ip
    gateway: !secret gateway_ip
    subnet: !secret subnet

  on_connect:
    - light.turn_on:
        id: led
        brightness: 100%
        red: 100%
        green: 65%
        blue: 0%

  ap:
    ssid: "${friendly_name}"
    password: !secret ap_password

captive_portal:

light:
  - platform: esp32_rmt_led_strip
    rgb_order: RGB
    pin: GPIO21
    num_leds: 1
    chipset: ws2812
    id: led
    rmt_channel: 0

# UART configuration
uart:
  id: ld2420_uart
  tx_pin: GPIO7
  rx_pin: GPIO6
  baud_rate: 115200
  parity: NONE
  stop_bits: 1

# LD2420 sensor configuration
ld2420:

text_sensor:
  - platform: ld2420
    fw_version:
      name: "LD2420 Firmware"
  - platform: wifi_info
    ip_address:
      name: "${friendly_name} IP Address"

sensor:
  - platform: ld2420
    moving_distance:
      name: "${friendly_name} Motion Distance"

binary_sensor:
  - platform: ld2420
    has_target:
      name: "${friendly_name} Presence"
      id: has_target

select:
  - platform: ld2420
    operating_mode:
      name: "${friendly_name} Operating Mode"

number:
  - platform: ld2420
    presence_timeout:
      name: "${friendly_name} Presence Timeout (s)"
    min_gate_distance:
      name: "${friendly_name} Minimum Distance (Gate)"
    max_gate_distance:
      name: "${friendly_name} Maximum Distance (Gate)"
    gate_select:
      name: "${friendly_name} Gate Selection (Gate Number)"
    still_threshold:
      name: "${friendly_name} Still Threshold (Sensitivity)"
    move_threshold:
      name: "${friendly_name} Motion Threshold (Sensitivity)"
    gate_move_sensitivity:
      name: "${friendly_name} Motion Sensitivity (Factor)"
    gate_still_sensitivity:
      name: "${friendly_name} Still Sensitivity (Factor)"

button:
  - platform: ld2420
    apply_config:
      name: "${friendly_name} Apply Config"
    factory_reset:
      name: "${friendly_name} Factory Reset"
    restart_module:
      name: "${friendly_name} Sensor Restart"
    revert_config:
      name: "${friendly_name} Revert Changes"